|
|
Post by vulbas on Dec 15, 2016 14:37:24 GMT
of course  |
|
|
|
Post by vulbas on Dec 15, 2016 19:55:08 GMT
Is it a problem if the AREF tracks are cut off.   |
|
|
|
Post by tronicgr on Dec 15, 2016 22:07:08 GMT
Is it a problem if the AREF tracks are cut off. No problem, it's not using the analog at all. |
|
|
|
Post by tronicgr on Dec 16, 2016 1:17:21 GMT
Another milestone. The 12-bit pwm is running perfectly. Now I need to tidy up the code before I can release a combined version with 12-bit input position feedback with 12-bit resolution output as well.
More on this soon!
Thanks
Thanos
|
|
|
|
Post by hexpod on Dec 16, 2016 16:34:05 GMT
Could you please post a link where you've bought yours ssi? |
|
|
|
Post by hexpod on Dec 16, 2016 16:37:31 GMT
Another milestone. The 12-bit pwm is running perfectly. Now I need to tidy up the code before I can release a combined version with 12-bit input position feedback with 12-bit resolution output as well. More on this soon! Thanks Thanos Great!!! ... Looking forward. |
|
|
|
Post by vulbas on Dec 16, 2016 19:05:14 GMT
@hexopod, what is ssi ? Today i changed the xlr plug. I am going from 3 points to 5 points. aujourd'hui j'ai changer les prise xlr. je suis passer de 3 points à 5 points   |
|
|
|
Post by tronicgr on Dec 16, 2016 22:58:15 GMT
vulbas SSI is short for Synchronous Serial Interface... 
|
|
|
|
Post by vulbas on Dec 17, 2016 8:02:19 GMT
It is the cable ? Sorry i'm a noob in electronic lol
|
|
|
|
Post by hexpod on Dec 17, 2016 12:50:07 GMT
vulbas SSI is short for Synchronous Serial Interface... The new digital sensors from the picture in your previous post. Where did you order them? Could you please post a link? Thanks |
|
|
|
Post by vulbas on Dec 17, 2016 13:32:48 GMT
|
|
|
|
Post by hexpod on Dec 18, 2016 7:52:44 GMT
|
|
gokhan
Junior Member
Posts: 89 
|
Post by gokhan on Dec 19, 2016 11:07:39 GMT
I would like to share two issues i am experiencing. 1. Garbage characters on screen, motors didn't react but i powered off immediately just incase. After reboot it didn't re-occur.  Here is the photo of it when it happened.  2. I set minimum speed to 1 and save it, like i save all the other changes. When i reset/ reboot the amc it sets it back to 10. All the other changes comes back as I set. Here is the video of it. www.youtube.com/watch?v=qoTVtdUfQA8Any ideas what goes wrong? |
|
|
|
Post by tronicgr on Dec 19, 2016 11:19:49 GMT
I would like to share two issues i am experiencing. 1. Garbage characters on screen, motors didn't react but i powered off immediately just incase. After reboot it didn't re-occur. Here is the photo of it when it happened. 2. I set minimum speed to 1 and save it, like i save all the other changes. When i reset/ reboot the amc it sets it back to 10. All the other changes comes back as I set. Here is the video of it. www.youtube.com/watch?v=qoTVtdUfQA8Any ideas what goes wrong? Thanks for the feedback. 1. Seems like the LCD did not initialize correct, was this after a reboot? 2. I'll check the routines that save the parameters and upload a corrected version for you to test again. Thanks Thanos |
|
gokhan
Junior Member
Posts: 89
|
Post by gokhan on Dec 19, 2016 11:34:27 GMT
It was during normal operation. I was trying different settings and all of a sudden it happened.
By the way what exactly "oversampling" does?
|
|
