|
Post by misoswan on Sept 14, 2015 19:37:38 GMT
|
|
|
Post by vicpopo on Sept 14, 2015 20:40:15 GMT
Here the right connecting diagram the setpoint coming from amc 6dof ext board is to AI11 connected AI12 to GND for the reference voltage
|
|
|
Post by tronicgr on Sept 14, 2015 22:15:01 GMT
Here the right connecting diagram the setpoint coming from amc 6dof ext board is to AI11 connected AI12 to GND for the reference voltage Hmm I don't remember if I updated that or not in the manual as well, I'll check. Thanks Thanos
|
|
|
Post by misoswan on Sept 15, 2015 7:09:52 GMT
hello ENGINE STILL NOT WORK I have everything connected ok.Unconnected has connected only emergency switch.the problem may be that? am all setting same :https://www.youtube.com/watch?v=RYwdS5HStP0 all work correctly.diagrams,conection board,3 dof simulation.connection in game.... only engine not work.
|
|
|
Post by tronicgr on Sept 15, 2015 10:57:26 GMT
In the video I think you show a potentiometer with only two wires connected... It should have 3wires! GND,+5v,signal
Can you confirm this?
Also increase the max motor speed for online AND offline to 50% or above! I think you also need to wire the emergency button or at least bond together these connections of the button as otherwise the motor won't function from remote(amc1280usb)
Thanks Thanos
|
|
|
Post by misoswan on Sept 15, 2015 12:37:49 GMT
hello yes i have conection all 3wires. and conection +emergenci switch.(settup online speed 90% and offline same 90% still not work this other video. www.youtube.com/watch?v=KvWAKNxiYOoneed? download Firmware in board? Red light is fine? if so, how to open it what program. Thanks Michal
|
|
|
Post by vicpopo on Sept 15, 2015 15:50:49 GMT
Maybe a silly question.In the video I noticed that you wired the pot feedback axis nbr 2.Are you sure that you wired the setpoint axis nbr 2 in the inverter and also for'the cw and ccw signals. It happened in the past to me and the motor runs continuously !
|
|
|
Post by misoswan on Sept 15, 2015 16:17:08 GMT
hi I checked connection inverter 2 all connected ...all is connected for inverter2
|
|
|
Post by misoswan on Sept 15, 2015 16:28:25 GMT
maybe connected sensor in ? ----What is what? Thanks
|
|
|
Post by misoswan on Sept 15, 2015 17:04:03 GMT
my setting
|
|
|
Post by vicpopo on Sept 15, 2015 18:11:41 GMT
Did you already test the others sensor position like pos 1 2 3 4 5 6 ?
|
|
|
Post by misoswan on Sept 15, 2015 18:19:20 GMT
I feel like I have not tested it 123456...
|
|
|
Post by misoswan on Sept 15, 2015 18:31:16 GMT
hello tested 123456 still not work
|
|
|
Post by tronicgr on Sept 15, 2015 19:26:15 GMT
Perhaps you didn't switch the VFD to Source mode? vicpopo is there a switch or metal bar bridge for the Source mode for digital inputs? Don't remember...
|
|
|
Post by misoswan on Sept 15, 2015 19:29:55 GMT
hello all NOW WORK YES YES An error was with me AN NOT CONNECTED CORRECTED POWER 24V Thank you all for your help.
|
|