While installing the new firmware 2.0 you may receive a error message "Buffer overflow :  > ". Look here about the setting in the AVRUBD to make it fit in the memory: motionsim.freeforums.net/post/324
If you notice any bugs or issues, please let me know to fix them asap.
hi thanos I noticed a difference between the "Software Fabi" and the menu of the AMC. you had advised me to put 1 oversample for optimum setting.
in the FABI soft menu, the cursor moves from 1 to 16 . bits ?? what is this setting? This is the same setting as the oversample AMC menu ??
can you explain here what is the function of setting the oversample AMC?
what is the best setting for precision and optimum results?
from the FABI software I understand that it adjusts the resolution of the potentiometer.
in this case should be adjusted to 16 bits?
But you counseled adjusting to 1 or 4 Thanks
Hmm I just noticed that as well. You are right its not bits, its number of samples thus the title "oversample".
So if you choose "1" it takes one sample of the analog inputs. If you choose "2" or more it takes multiple samples and uses their average value, which kind of filters out noise and increases a little bit the resolution near 16bit level. The tradeoff is a slower cycle speed of the controller that in some fast motors might translate in instability.
It adds a selectable ramp increase in speed while switching between on-line and offline mode. You can change the delay of the ramp in a new sub menu under the Max Motor speed menu. The delay is in ms 0-10ms, with 0ms disables the ramp completely. The ms delay is from the cycle that lasts usually 1ms, so it will delay the normal run cycle by the amount you add to the ramp, but don't worry, it lasts only during the ramp, not all the time.
This beta version is not fully tested yet, but any feedback on its behavior is welcome.
dureiken: Hi there, it's really quiet here someone could help me for my 6 dof project ? thanks a lot
Aug 8, 2017 15:34:46 GMT
tronicgr: dureiken Hi, Open a thread and I'll try my best to help. A little busy with Kickstarter details at the moment but I'll see what I can do.
Aug 12, 2017 11:57:42 GMT
dureiken74: I just did it
Aug 27, 2017 11:59:06 GMT
fimmy: How's the firmware going?
Sept 6, 2017 8:34:43 GMT
tronicgr: @fimmy I had to put it on hold to finalize the manufacturing of the new kickstarter controllers. I tested parts of it to ensure compliance with the new features and looks good so far. I'll get back to it soon for integration.
Sept 9, 2017 12:52:35 GMT
Theuns: Very nice design.I'm also busy with mine and changing it also to Linear Actuators with 220v Servo motors.I'm waiting for my new controllers from Thanos. If I may ask Do you have any Sketchup files of your design and willing to share it I Thanks Theuns
Sept 14, 2017 22:45:09 GMT
atayeu: Hey everyone! I'm reading up and gathering all of the intel I can find for my first motion platform. this is by far best information for creating one.
Oct 14, 2017 7:25:57 GMT
tmcnam: I must be crazy but I still can't find the blueprints to the platform by GA-Dawg. Any help would be appreciated. Thanks guys.
Mar 10, 2019 21:31:57 GMT
Trip Rodriguez: Sorry tmcnam, the shoutbox doesn't get much attention. Did you find the blueprints? They are at the VERY bottom of the extremely long first post. It says "attachments: 6DOF.zip
May 4, 2019 19:13:25 GMT
zivby: How much weight this setup can carry?
May 19, 2019 11:57:16 GMT