|
Post by riton39 on Jul 28, 2017 14:55:35 GMT
Thanos, i have always the same problem with the new firmware: www.youtube.com/watch?v=QehJC9NZ21o&feature=youtu.bewhen i press start the motor 2 move abnormally , see the video. I've already replaced the little card 6 DOF, same problem. the problem seems to come from the AMC or the Firmware. This problem happened with the update of the Firmware I feel that it's from the USO; with the 6DOF plugin, the problem seems not exist. is it possible to put the plugin interface 6dof and configure Xsim to my 2DOF? can you fix the problem that it works as before the update of the Firmware of the AMC? I'd like to find a solution, my Simulator is unusable thanks
|
|
|
Post by riton39 on Jul 31, 2017 21:35:50 GMT
Thanos, I wrote several messages, by mail, on your forum, you do not seem to want to answer me ?? Nevertheless, you are attentive to what is happening here What should I do to restart my simulator? I would like to find a solution. . I would like a discussion, an exchange to move forward and find a solution. I would be really glad that my simulator works again, that you give me a little of your time
Thank you in advance
|
|
|
Post by tronicgr on Aug 2, 2017 11:05:51 GMT
Thanos, i have always the same problem with the new firmware: www.youtube.com/watch?v=QehJC9NZ21o&feature=youtu.bewhen i press start the motor 2 move abnormally , see the video. I've already replaced the little card 6 DOF, same problem. the problem seems to come from the AMC or the Firmware. This problem happened with the update of the Firmware I feel that it's from the USO; with the 6DOF plugin, the problem seems not exist. is it possible to put the plugin interface 6dof and configure Xsim to my 2DOF? can you fix the problem that it works as before the update of the Firmware of the AMC? I'd like to find a solution, my Simulator is unusable thanks Hi, First you need to check if your controller is working correct. Follow the instructions in these videos to see if the outputs are correct: www.youtube.com/watch?v=e8X8YMFrp-wwww.youtube.com/watch?v=PqsPKYejMgAThen you need to set the controller in 6DOF and test manually the sliders to see if there is correct motion using the 6DOF plugin. www.dropbox.com/sh/8jexs5optuljr27/AABtfTrGArD2-_2vn3oFLNk5a?dl=0You could take videos of testing the above to see if I can notice the issue, as from your video I can't tell what can be wrong. From the motion alone can't tell if its bad position sensor or bad output (electrical issue) as I'm not there to measure the voltages with a multimeter. Perhaps the AMC1280USB controller you have got damaged electrically, it can happen. In that case I could replace with new one if you send it to me, or you could get advantage of the kickstarter offer only for existing AMC1280USB owners and get two controllers (the second to replace you old controller) in the half price for one, just $190 (AMC1280USB Basic pledge option). But hurry, the kickstarter is almost finished! Thanks Thanos
|
|
|
Post by riton39 on Aug 2, 2017 16:02:43 GMT
It works perfectly with the 6DOF plugin, I could test with your plugin 6dof soft movements. My 2 Motors move properly without the filmed parasite movements of my video. This is what I noticed using the 6DOF with Xsim plugin. Same problem with Simtool reminder, I have a 2DOF, I enter Xsim characters. all right until I press Start in Xsim.
so it seems there's some movement parasite only via the config of the characters:
AB ~ a02 ~ ~ a01 ~. AB ~ 127 ~ ~ 255 ~ ~ 127 ~ ~ 255 ~.
|
|
|
Post by riton39 on Aug 2, 2017 17:50:32 GMT
The side motor, effect 25 sends control peaks to the frequency converter. This happens only on this engine, I have already tested everything, reversed the motors, changed the potentiometer, change the small 6DOF card. That this product only on this engine, and that with the characters in Xsim, simtools. I have not noticed this problem with the 6DOF plugins. I have already given the details of this problem for a long time and several times. Another video: youtu.be/277XFEimmkA
|
|
|
Post by riton39 on Aug 4, 2017 16:21:05 GMT
I'll make you a paquet with your cards. The AMC 64 is obsolete, I have too much PID problem and encoder problem with this card My AMC 128 does not work anymore since the firmware update ... You obviously have no time to look at the problem. I hope your new card works in 2DOF without the same problem as me ?? Make me a commercial proposal for the replacement of my 2 cards. Give me also your address for the shipping of the cards. Richard
|
|
|
Post by tronicgr on Aug 6, 2017 17:07:10 GMT
I'll make you a paquet with your cards. The AMC 64 is obsolete, I have too much PID problem and encoder problem with this card My AMC 128 does not work anymore since the firmware update ... You obviously have no time to look at the problem. I hope your new card works in 2DOF without the same problem as me ?? Make me a commercial proposal for the replacement of my 2 cards. Give me also your address for the shipping of the cards. Richard No need to send me your old boards. You can choose any of these two options offered here: motionsim.blogspot.com/2017/08/extending-pre-orders-for-kickstarter.htmlYou will receive two controllers instead of one. (Existing owner special offer) Thanks Thanos
|
|
|
Post by riton39 on Aug 7, 2017 8:45:25 GMT
Ok, thanks , I send you an e-mail.
|
|
|
Post by tronicgr on Aug 7, 2017 22:33:21 GMT
Ok, thanks , I send you an e-mail. Ok, check your email, there is a couple from me there. Thanks Thanos
|
|
|
Post by riton39 on Aug 13, 2017 16:55:42 GMT
Ok, i sent the Payment.
As you do the tests in 2DOF with Xsim in my configuration? You do not have my problem of control on the engine 2?
I was thinking about a soft problem ...
I do not explain the breakdown of my AMC. This really appeared after the firmware update. I really do not like not understanding the cause of the problems.
|
|
|
Post by riton39 on Aug 13, 2017 18:10:46 GMT
I saw your comment on my YouTube video on my problem, that's not the cause of the problem.
the parasite movements are present as soon as I press Start in Xsim. no need to effect in the simple Xsim done press Start of the parasitic movement on engine 2, it really comes to the AMC
This don't does not so much matter if the new card works perfectly in my configuration, of course, but I would not discover the same problem upon receipt of the cards.
I'd like to be certain that this is a failure of my card and not a problem of Firmware or a bug hidden.
|
|
fimmy
New Member
Posts: 16
|
Post by fimmy on Aug 14, 2017 5:37:38 GMT
Just test the new card. Then you will know if card problem or firmware. If firmware I am sure Thanos will take the card back. If your card was faulty then you have sorted the problem. Relax and see what happens. If it works once before , it can work again
|
|
|
Post by tronicgr on Aug 15, 2017 11:55:22 GMT
I saw your comment on my YouTube video on my problem, that's not the cause of the problem. the parasite movements are present as soon as I press Start in Xsim. no need to effect in the simple Xsim done press Start of the parasitic movement on engine 2, it really comes to the AMC This don't does not so much matter if the new card works perfectly in my configuration, of course, but I would not discover the same problem upon receipt of the cards. I'd like to be certain that this is a failure of my card and not a problem of Firmware or a bug hidden. Could be also faulty FTDI chip on the controller you have. I have seen similar issues before, where the controller works firn to load the firmware in lower speeds (19kbps) but as soon you use full speed 250kpbs it inserts garbage characters that confuse the controller. I had this happen in the really old blue color ATMega1280 boards. Can you send a photo of the base ATmega board that has the USB input (base board that the AMC1280USB board sits on it). Thanks Thanos
|
|
|
Post by riton39 on Aug 15, 2017 13:01:43 GMT
my card is black. I met problems with the firmware update. I have done several attempts because the display remained blocked on a blank display, no info displayed. I had other views bugs but the latest firmware went well. the update of the firmware on the old 2.0 version does not resolve the failure
|
|
|
Post by tronicgr on Aug 16, 2017 11:32:57 GMT
my card is black. I met problems with the firmware update. I have done several attempts because the display remained blocked on a blank display, no info displayed. I had other views bugs but the latest firmware went well. the update of the firmware on the old 2.0 version does not resolve the failure Ok, no problem, we'll figure this out. Thanks Thanos
|
|